Startup for Motorola PowerPC MVME series VME boards (QNX Neutrino)
startup-mvme [-A] [-D channel[.channel_opts]] [-E]
[-j addr] [-K channel[.channel_opts]]
[-R size] [-r addr,size[,flag]]
[-S [~]section] [-v[v]...]
Motorola MVME series VME boards (PowerPC)
- Reboot the system on any abnormal termination of the kernel.
The default is to display information about the crash, and then halt.
- -D channel[.channel_opts]
- Specify an output channel for debugging information. See below
- Enable Procnto-600 to save and restore the EAR (External Address Register)
register (on chips that have it) during context switches. The EAR register will be
saved/restored only if the -E option is set.
- -F [~]value
- Control the flags field in the cpuinfo section of
- value -- OR the flags field with
- ~value -- AND the flags field with
||The option was added in the
QNX Neutrino Core OS 6.3.2.|
For more information about the flags, see "Structure of the
system page" in the Customizing Image Startup Programs chapter of the
Building Embedded Systems guide.
- -f [cpu_freq][,[cycles_freq][,timer_freq]]
- Specify CPU frequencies.
All frequencies can be followed by H for hertz,
K for kilohertz, or M for megahertz
(these suffixes aren't case-sensitive). If no
suffix is given, the library assumes megahertz if the
number is less than 1000; otherwise it assumes hertz.
If they're specified, cpu_freq, cycles_freq, and
timer_freq are used to set the corresponding variables
in the startup code:
- cpu_freq -- the CPU clock frequency. It's also used
to set the speed field in the cpuinfo section of the
- cycles_freq -- the frequency at which the
value returned by
ClockCycles() increments. It's also used to set the
cycles_per_sec field in the qtime
section of the system page.
- timer_freq -- the frequency at which the timer chip
input runs. It's also used to set the timer_rate and
timer_scale values of the qtime section of the
If a variable is zero when it comes time to set the field(s)
on the system page, the library code attempts to deduce the proper
value by using one of the other frequency variables. Which one it uses
depends on the particular CPU and hardware.
- -j addr
- For use with JTAG/hardware debuggers.
Reserve 4 bytes of RAM at the physical address
specified by addr, and copy the physical address
of the location of the system page to addr
in RAM so that it can be retrieved by a hardware debugger.
- -K channel[.channel_opts]
- Specify an output channel for kernel debugger information. See
below for details.
- -N hostname
- Specify the node name. The default is the local host.
- -R size
- Remove size memory from system use. This is useful for
testing in a restricted-memory environment.
- -r addr,size[,flag]
- Remove size memory from system use
starting at addr.
The flag is an optional
argument used to specify if the memory should be cleared:
|If the value of the flag passed is:
||Clears to 0
||Clears to 0
||Does not clear
- -S [~]section
- Turn on (or, if you use ~section, off) output
of the specified syspage section's information. Use this
to restrict the amount of syspage information.
For more information, see the description of
in the Customizing Image Startup Programs chapter of Building Embedded Systems.
- Be verbose. More v characters cause even more
- Enable extended addressing.
This lets you access physical addresses above 4G.
|| This option has an effect only if the CPU supports more than 32 address
On PowerPC CPUs, extended addressing is supported if the
PPC_CPU_XAEN bit is on in the
For more information, see
"Structure of the system page"
in the Customizing Image Startup Programs chapter of
Building Embedded Systems.
The debug channel specified with the -D and -K options
- Use a generic 8250-compatible serial chip, with:
- Specify the I/O port base address for the 8250, in
The default port for the -D option is
the default for the -K option is
- Specify the spacing between the I/O registers, in
The default is 0.
- Specify the baud rate for the debug channel. The default is
- Specify the clock rate (in Hz) input to the chip. The
default is 1846200.
- Specify the divisor used on the clock rate by the chip. The
default is 16.
You can skip options by leaving out the data associated with that part. For
example, if you want to send the debugging output to an 8250 chip using
57600 baud, use:
The default -D and -K settings are:
The startup-mvme program is responsible for initializing the
MVME series VME boards.
"Startup programs (startup-*)"
in the Utilities Summary chapter
Customizing Image Startup Programs in Building Embedded Systems